Tiered Alabaster Wall Sconce
VKW4-26612-01
- In stock, ready to ship
A sculptural wall sconce — five horizontal alabaster panels, staggered like a slow geometric ladder, lit from within by a warm-white LED bulb. The natural stone glows softly between the stainless-steel supports; the form reads as a quiet wall sculpture, lit or unlit. 10.2″ × 13.8″ × 8.7″ projection (26 × 35 × 22 cm). For foyers, gallery walls, stairwells, and statement bedrooms.
Five tiered panels
Hand-shaped horizontal alabaster panels stagger out from the wall in a quiet geometric rhythm.
Natural stone glow
A warm-white LED bulb behind the panels lights the natural alabaster on both faces.
Stainless-steel support
Slim stainless-steel armature holds the panels in place; the support disappears against the glow.
| Material | Alabaster, Stainless Steel |
| Panels | Five hand-shaped horizontal alabaster panels, staggered |
| Support | Stainless-steel armature |
| Light source | One E27 medium-base bulb · max 40W (LED recommended) |
| Light color | Warm white (pick bulb temperature to taste) |
| Size (W × H × Proj.) | 10.2″ × 13.8″ × 8.7″ (26 × 35 × 22 cm) |
| Power | AC 110–240V; hardwired over a standard junction box |
| Control | Wall switch on/off |
| Use | IP20 indoor and dry locations only |
Click the diagram to enlarge.
W10.2″ × H13.8″ × Proj.8.7″ 26 × 35 × 22 cm
🔍 Click to open full size in a new tab
Natural alabaster — each piece is one of a kind
Each panel is hand-shaped from natural alabaster, with its own veining, color shifts, and small inclusions. No two sconces will look identical — variation from photos is expected, not a defect. Email us for photos of in-stock pieces before ordering.
Deep projection — measure before ordering
This sconce projects 8.7″ (22 cm) from the wall, which is deeper than a typical sconce. Plan for clearance in hallways, beside doorways, and around traffic paths — install where it can sit unobstructed.
- Hardwired wall mount over a standard junction box — a licensed electrician is recommended.
- Use one E27 medium-base bulb, max 40W (or LED equivalent). Use LED only — incandescent and halogen bulbs run hot enough to discolor natural alabaster over time. Bulb not included.
- Controlled by a standard wall switch (on/off). Not designed for external dimmer compatibility — pair with a standard switched circuit.
- Indoor and dry locations only (IP20). Safe in damp vanity areas away from shower spray; not rated for wet zones. Confirm your local code before bathroom installation.
- Handle the alabaster panels gently during install — natural stone can chip if knocked. Once mounted, the sconce is stable; the risk is during unpacking and hanging.
- Dust the panels with a soft, dry cloth. No water or solvents on the stone; the stainless-steel armature can be wiped with a barely-damp microfiber.
Is the alabaster real natural stone?
Yes — each panel is hand-shaped from a single piece of natural alabaster. The stone's translucency lets a warm-white LED bulb glow through both faces. Veining, color, and small inclusions are unique to each piece.
Where does it fit best?
Foyers, gallery walls, stairwells, statement bedrooms, dining-room accents. Best on a flat unbroken wall where the staggered panels read against open background. The 8.7″ projection means it isn't a low-profile sconce — give it space.
What bulb does it take, and how bright is it?
One E27 medium-base bulb, max 40W (or LED equivalent), not included. Use a warm-white LED only — incandescent and halogen run hot enough to discolor natural alabaster over time. The light is soft and ambient through the stone — accent and mood light, not whole-room lighting. Pair with ceiling or table lights for general illumination.
Is it dimmable?
The sconce is controlled by a standard wall switch (on/off). It's not designed for external dimmer compatibility — using a dimmer on the wall circuit may cause flicker or shorten the LED life. Use a standard switched circuit.
What's the warranty?
2-year warranty on wiring, socket, and finish. Natural stone veining and inclusions are not defects; chips from drops or knocks during install or use, and alabaster discoloration from using an over-spec or non-LED bulb, are not covered. Email support with photos within 7 days of delivery for any transit damage.
Sizing & questions
Every piece is made to order in our own atelier — here is what most clients ask before choosing theirs.
What are the exact dimensions and projection?+
W 10.2″ × H 13.8″ × D 8.7″ (26 × 35 × 22 cm). The 8.7″ projection is deeper than typical wall sconces—measure clearance in hallways and near doorways before installing.
Is the alabaster real natural stone?+
Yes. Each panel is hand-shaped from solid natural alabaster. Veining, color shifts, and small inclusions vary by piece—no two sconces are identical. Email us for photos of in-stock pieces before ordering.
What bulb does it use and how bright is it?+
One E27 medium-base bulb, max 40W (LED recommended, not included). Use warm-white LED only—incandescent and halogen run hot enough to discolor the stone over time.
Where does this sconce work best?+
Foyers, gallery walls, stairwells, statement bedrooms, and dining accents. Install on a flat, unbroken wall where the staggered panels read against open background. Give it space—the projection is substantial.
What's involved in installation and care?+
Hardwired over a standard junction box by a licensed electrician. Handle alabaster panels gently during unpacking—natural stone can chip. Dust with a soft dry cloth; wipe the stainless-steel armature with barely-damp microfiber only.
Downloads
If it is a product quality problem or transportation damage, we will provide free return and exchange services, ensuring a hassle-free experience for our customers. Read the full Return & Refund Policy; if your order arrives damaged, see what to do when you receive a damaged item (report within 72 hours) and our shipping & tracking guide.
Design with confidence: Vakkerlight 3D Lighting Design Service
Take the guesswork out of lighting design. Whether for residential or commercial spaces, our 3D Lighting Design Service lets you visualize and customize fixtures in a realistic 3D environment before you buy.
- Personalized solutions: custom arrangements tailored to your exact space.
- True-to-life 3D: see how your fixtures will look before installation.
- Expert support: 1-on-1 guidance from our design specialists.
Resources & support: visit the 3D Lighting Design Service page to learn more. Need 3D Max files or detailed product parameters? Email info@vakkerlight.com and our team will be happy to assist you.
Product cut sheets (Google Drive) →
Welcome to Vakkerlight’s 3D Services. We pride ourselves on offering comprehensive design support to meet all your lighting needs. If you require 3D drawings, CAD plans or space design services, our experienced support team is here to help — email info@vakkerlight.com.
