Volos Dome Table Lamp
VKT04-2672-04
- الشحن القياسي إلى الولايات المتحدة
- تغطية الضمان متاحة
- إرجاع لمدة 60 يومًا على العناصر المؤهلة
- دعم العملاء عبر البريد الإلكتروني & الهاتف
- التخصيص الشخصي متاح
- تتوفر خيارات شحن متعددة
- مدفوعات آمنة ومأمونة
- متوفر بخيارات كهربائية خاصة بالمنطقة
- In stock, ready to ship
A table lamp built around two integrated LED modules — no bulb socket, no bulb to source or replace. The walnut-finish wood body pairs with satin metal hardware in a single coherent finish: warm brown grain against cooled metal, a combination that reads as furniture-grade rather than purely utilitarian. At D25 × H35 cm the lamp sits proportionately on a bedside table, desk, or console without dominating the surface. Both 12W LED arrays run at 3000K warm white — the light output is fixed at that color temperature with no user-adjustable switching.
Integrated LED — no bulb required, no bulb to replace
The light source is built into the fixture. There is no user-replaceable bulb — the LED modules are a permanent part of the lamp body. When the LED reaches end of life (typically 25,000–50,000 hours of use), the fixture itself would need servicing or replacement. No separate bulb purchase is needed at any point.
Plug-in table lamp — no electrician required
This is a plug-in table lamp that connects to a standard wall outlet. No hardwiring or ceiling installation is needed. Confirm plug type and voltage compatibility for your market before ordering — see specifications below.
Integrated LED · no bulb
Two 12W LED modules (24W total) are built into the lamp body. No socket, no bulb hunt — plug in and it is ready. LED lifespan is rated at 25,000+ hours under normal use.
Walnut + metal body
Walnut-finish wood and satin metal hardware — the same material pairing found in mid-century and Japandi furniture. The two materials share a warm, low-contrast palette without competing for attention.
3000K warm white
Fixed 3000K color temperature — warm enough to sit comfortably on a bedside or desk without the yellow cast of older incandescent bulbs, cooler than a candle flame but warmer than daylight.
Walnut Color — single colorway
Walnut-finish wood body paired with satin metal hardware. The warm brown grain of the walnut reads against the cooled metal without a strong contrast — the two materials sit in the same warm-neutral register.
2 × 12W integrated LED · 3000K · non-replaceable · ~24W total
Two 12W LED modules are built permanently into the lamp body — one per light-emitting element. Both run at 3000K warm white with no color temperature switching. Total output is approximately 24W, equivalent to a 150–200W incandescent in lumen output at that color temperature. The LED driver is internal; whether the lamp is dimmable depends on the driver specification — confirm before purchasing if dimming is required. LED rated lifespan: typically 25,000–50,000 hours under rated conditions.
🔍 Dimensions — tap to enlarge
| Light source | Integrated LED — non-replaceable · 2 × 12W modules · ~24W total |
| Color temperature | 3000K warm white (fixed — no CCT switching) |
| Dimensions | D25 × H35 cm (D9.8″ × H13.8″) |
| Finish / color | Walnut Color — single colorway |
| Material | Metal + walnut-finish wood |
| Lamp type | Plug-in table lamp |
| Input voltage | CONFIRM BEFORE PUBLISHING — confirm 110–240V universal or region-specific |
| IP rating | IP20 — indoor, dry locations only |
| Dimmable | CONFIRM BEFORE PUBLISHING — depends on internal LED driver specification |
| LED lifespan | ~25,000–50,000 hours (rated) |
| Best for | Bedside table · desk · console · sideboard · Japandi · mid-century · Scandinavian · transitional interiors |
Single configuration
One size and one finish (Walnut Color). No variants to select. Email us for trade or bulk pricing.
- Plug the lamp into a standard wall outlet. Confirm voltage compatibility before use — check the label on the cord or driver for input voltage range. Do not use a voltage incompatible with your local supply without an appropriate transformer.
- The integrated LED modules require no setup — the light is built in and ready at first power-on. There is no bulb to install or replace.
- If the lamp has a dimmer switch: confirm the driver is dimmable before connecting to a dimmer circuit. Connecting a non-dimmable driver to a dimmer may cause flickering, buzzing, or driver damage.
- Do not place in direct sunlight for extended periods — UV exposure can fade the walnut finish over time. Position away from sustained moisture sources (humidifiers, open bathroom doors).
- Walnut-finish wood: wipe with a soft dry cloth. Avoid water, alcohol-based cleaners, and abrasive pads, which strip the surface finish. For fingerprints, a very slightly damp cloth followed immediately by a dry cloth is sufficient.
- Metal hardware: dry microfiber cloth only. Avoid liquid cleaners and abrasive pads.
- LED diffuser / lens surface: wipe gently with a soft dry cloth only when the lamp has been off and fully cooled. Do not press hard on the LED surface.
Does it need a bulb?
No. The light source is built into the lamp body as two integrated 12W LED modules — there is no socket and no bulb to purchase or install. Plug it in and it is ready. Because the LEDs are integrated, they cannot be replaced when they reach end of life; the rated lifespan is approximately 25,000–50,000 hours under normal use conditions, which represents many years of typical household use.
What does "2 × 12W" mean?
The lamp contains two separate LED light-emitting modules, each rated at 12W, for a total output of approximately 24W. Both modules run at 3000K warm white simultaneously — there is no way to operate one module independently of the other, and there is no color temperature switching. The two-module design distributes light more evenly across the lamp body compared to a single central source.
Is it dimmable?
Dimming capability for an integrated LED lamp depends on the internal LED driver, not a user-replaceable bulb. Confirm with the supplier or product documentation whether the driver supports Triac (leading-edge) or trailing-edge dimming before purchasing if you plan to connect it to a wall dimmer. Connecting a non-dimmable driver to a dimmer circuit can cause flickering, buzzing, or driver damage. If the spec sheet confirms dimmability, use a compatible dimmer rated for LED loads.
Can I use this in the US with standard outlets?
Confirm the input voltage range on the cord or driver label before use. If the lamp is rated for 110–240V universal input, it will work on US 120V outlets with the correct plug type. If it is rated for 220–240V only, a step-up transformer is required for US use — not recommended for permanent lamp use. Check the plug type as well: a US-market lamp should have a standard Type A (two-blade) or Type B (two-blade + ground) plug.
What interior styles does this suit?
The walnut-finish wood and satin metal combination works naturally in Japandi, mid-century modern, Scandinavian, and transitional interiors that pair warm wood tones with cooled metal accents. The proportions (D25 × H35 cm) are compact enough for a bedside table without being too small to read by, and restrained enough for a desk or console without competing with objects around it. It does not suit maximalist, industrial, or cool-contemporary rooms where warm wood reads as too soft.
What happens when the LED reaches end of life?
Because the LED modules are integrated and non-replaceable, the lamp would need to be replaced or professionally serviced when they fail. Under typical household use (4–6 hours per day), a 25,000-hour rated LED lifespan represents approximately 11–17 years of use before the modules approach end of life. Actual lifespan varies with usage patterns, ambient temperature, and driver quality.
في حالة وجود مشكلة في جودة المنتج أو تلف أثناء النقل، سنقدم خدمات الإرجاع والاستبدال المجانية، مما يضمن تجربة خالية من المتاعب لعملائنا.
ورقة بيانات المنتج
صمم بثقة: خدمة إضاءة ثلاثية الأبعاد من فاكرلايت
تخلص من التخمين في تصميم الإضاءة. سواءً للمساحات السكنية أو التجارية، تتيح لك خدمة تصميم الإضاءة ثلاثية الأبعاد المبتكرة من Vakkerlight تصور وتخصيص وحدات الإضاءة في بيئة ثلاثية الأبعاد واقعية قبل الشراء.
- حلول مُخصصة: ترتيبات مخصصة مصممة خصيصًا لمساحتك.
- تقنية ثلاثية الأبعاد واقعية: تعرّف على شكل تجهيزاتك قبل تركيبها.
- الدعم الفني المتخصص: احصل على إرشادات فردية من متخصصي التصميم لدينا.
موارد & يدعم:
تفضل بزيارة صفحة [خدمة تصميم الإضاءة ثلاثية الأبعاد] لمعرفة المزيد. هل تحتاج إلى مساعدة؟ ملفات 3D Max هل تحتاج إلى معلومات تفصيلية عن المنتج؟ راسلنا عبر البريد الإلكتروني على: info@vakkerlight.com وسيسعد فريقنا بمساعدتك.
